Hi everyone, I host a server with few services running for my family and friends. The server freezes sometimes. Where the services stop responding. If I try to ssh into the server, it takes a lot of time (3 to 5 mins) for it to connect. After being connected, every letter I type takes 2 to 3 mins to appear on screen.

Seems like the server is overloaded with tasks. But I am not sure what load it is running. I have netdata installed. I could pull up following screenshots for insights.

Can someone please help me in troubleshooting the issue?

I have tried testing stress testing my RAM and CPU, and they were fine. But I would start troubleshooting from scratch if you have recommendations for testings softwares.

Please also let me know if there is anything I can pull from netdata to help in trouble shooting.

System Specification:

System RAM

Disk I/O

Total CPU Utilization

Idle Jitter

  • WhyAUsername_1@lemmy.worldOP
    link
    fedilink
    English
    arrow-up
    5
    ·
    1 year ago

    Superb. I will do that. Would increasing ram Capacity solve the issue? Also, does High IO wait time indicate issue with the boot drive (which is an SSD that is 4 years old)

    • EinfachUnersetzlich@lemm.ee
      link
      fedilink
      English
      arrow-up
      14
      ·
      edit-2
      1 year ago

      Would increasing ram Capacity solve the issue?

      It depends whether the problem is that you don’t have enough RAM, or something is using more RAM than it should. In my experience it’s almost always the latter.

      Also, does High IO wait time indicate issue with the boot drive (which is an SSD that is 4 years old)

      No, it means the CPU is waiting for disk I/O to complete before it can work on tasks. When available RAM is low, pages get swapped out to disk and need to be swapped back in before the CPU can use them. It could also be an application that’s reading and writing a huge amount from/to disk or the network, but given the high memory usage I’d start looking there.

      • WhyAUsername_1@lemmy.worldOP
        link
        fedilink
        English
        arrow-up
        1
        ·
        1 year ago

        Okay. Thanks for the insight. Planning to do this:

        You need to monitor which process is using all the memory. The easiest way is probably to keep htop running in a screen or tmux session, periodically connect, and look at which processes have the highest used memory.

        Will report back with findings when it crashes again. Thanks for all the help.

        • EinfachUnersetzlich@lemm.ee
          link
          fedilink
          English
          arrow-up
          1
          ·
          1 year ago

          It’ll probably be obvious before it crashes, you can see in the graphs that the “used” memory is increasing steadily after a reboot. Take a look now and see which process is causing that.

    • cbAnon0@lemmy.world
      link
      fedilink
      English
      arrow-up
      3
      ·
      1 year ago

      Difficult to read the graph, but looks like you have less than 4GB ram. Depending what sort of OS and services are running (from above suggestions), this is likely the biggest issue.

      You haven’t mentioned which services you’re running, but 4GB might be enough perhaps for a basic OS with NAS file share services. But anything heavier, like running Container services will eat that up. You’d want at least 8GB.

      Note also that you may not have a dedicated graphics card? If you have integrated graphics, some ram is taken from System and shared with the GPU. If you’re just running command line, you might eke out a little more RAM for system by reducing the VRAM allocation in your BIOS. See: https://en.m.wikipedia.org/wiki/Shared_graphics_memory

    • vegetaaaaaaa@lemmy.world
      link
      fedilink
      English
      arrow-up
      2
      ·
      1 year ago

      look at which processes have the highest used memory

      You can also do that from the Applications menu in netdata, mem chart.

      I would also check the swap usage chart, I also think parent poster is correct and you are running into memory exhaustion, systems suddenly starts swapping like mad, disk I/O spikes, causing general unreponsiveness.